Value Added Value Engineering – Supporting your Goals

solutions. sustainability. success.

Solutions. Sustainability. Success.

  • Material Offsets: Maintaining Performance / Minimizing Costs on both Polymers as well as Over-Molded Substrates, Specification vs. Application Assessments
  • Cycle Time Improvements: Molding Multiple Components into One
  • Design Enhancements: Ergonomics, Fit and Assembly Efforts, Manufacturability
  • Quality Improvements: Cost Avoidance
  • Performance Improvements: A Better “MouseTrap”, Cost Avoidance
  • Material Savings: Wasteless & Flashless Tooling
  • Time Savings: Elimination of Secondary Processes
  • Pro-Active Project Alignment: Production Intent Proto-Typing, Design Support for Manufacturability, Material Development, APQP Process, Lean Manufacturing Focus

roadmap

material offsets

Material Offsets

Maintaining Performance / Minimizing Costs on both Polymers as well as Over-Molded Substrates, Specification vs. Application Assessments

  • Are you “squirrel hunting with an elephant gun”? Is your material specification aligned with the application or performance requirements?
  • Do you have restricted chemicals in your current polymers?
  • Is your current supplier proactively evaluating critical raw material offsets in case of a force majeure or prior to their obsoletion?
  • Senior formulating chemists on staff.
  • Small batch capabilities.
  • Strategic alliances with certified, high quality metals providers.
Rubber design enhancements
Rubber performance enhancements

Design Enhancements

Ergonomics, Fit and Assembly Efforts, Manufacturability

  • Consider Rahco Rubber as an extension of your staff! We’re here to help design in performance and ensure scrap is mitigated due to molding restrictions.
  • Capitalize on our fit, finish and part utilization expertise.

Performance Improvements

A Better “MouseTrap”, Cost Avoidance

  • Benefit from on our intellectual properties and experience 1st to ensure overall performance, avoid costs over and project delays.
Rubber Molding project alignment

Pro-Active Project Alignment

Production Intent Proto-Typing, Design Support for Manufacturability, Material Development, APQP Process, Lean Manufacturing Focus

  • Our APQP process keeps all parties on the “same-page”. Each threshold or stage-gate of a project crossed together making sure progress is sustainable.
  • Rahco Rubber takes full responsibility for keeping agreed to timelines as well as clear & transparent communications.

DMAIC roadmap

Wasteless & Flashless Molding

  • Material Savings – Nearly Zero Off-Fall.
  • Time Savings – Elimination of Secondary Processes.
  • Mold to Packaging Efficiencies, Cost(s) Elimination.
  • Positive Environmental Impact – Landfill Reduction.
  • Logistics & Inventory Cycle Time Improvements – Cost Minimization and/or Avoidance.

Wasteless Molding Processes

Our Wasteless Molding Technology can save you rubber compound and provide faster mold cycle times saving you *71%. “Wasteless” molding is probably the greatest improvement in rubber molding in the 20th century. The 21st century has brought new techniques that have made the wasteless process even more efficient.

While the initial reason for “Wasteless” molding was obviously to save compound, it has also been shown to cut cycle times due to heating less rubber compound in each heat due to the absence of a “rubber pad.” The image shows a typical “Wasteless” mold, which will be, run under a cold pot system. The “Wasteless” molding process can be used in transfer or injection molding. It can also be used in conjunction with the “flashless” or “flashfree” process.

 

 

 

The fabric sheets shown above are examples of the minimal rubber waste pad, which is discarded when using the Wasteless process. As you can see, only the sprues and, in some cases, a small runner is wasted.
low waste rubber molding Before/Waste Pad
Before/Waste Pad
Wasteless Rubber Molding
After - Waste Reduced from 462 Grams to 9 Grams
wasteless rubber molding
Waste
wasteless rubber molding
Wasteless

*cost avoidance by materials + efficiencies

Plastic Molding

plastic injection molding

In addition to molding rubber parts, we also have a separate manufacturing cell to concentrate on custom Injection Molding of engineered plastic components. We utilize the latest state of the art technology with our Engels and Arburg presses that range in size from 60 tons up to 150 tons. We work with just about all plastic resins as well as many different types of TPE’s. In addition to conventional molding, we also over mold materials such as TPE bonded to filled or unfilled Polypropylenes and Nylons as well as many other engineering grade resins.

Secondary Operations

Assembly

Customers often find it cost effective and easy to have us perform various assembly operations for them. This can range from a highly automated cell to simple packaging of various components.

Automation/Vision

We are always looking for that next technical advantage to define our expertise. We have automation cells in service for part assembly and boxing, rubber part slitting and robotic part removal of molded parts. We also incorporate vision systems where appropriate.

Slitting

Another specialty of ours is slitting of molded parts. This is the most common in valves where the slit creates a “normally closed” condition.

Cryogenics

After molding the part, we often aren’t finished. Cryogenic de-flashing systems are computer controlled to precisely control flash removal without damage to the part. In this process, the parts are cooled to the embrittling point of the material. Once brittle, the parts are subjected to a fine mesh media which helps to break off the excess flash.

Post Curing

Some applications require that the molded parts be post-cured. This is also true of some elastomers such as FKM and Silicones. To accomplish this we have modern, calibrated ovens to ensure accurate temperature and time, from batch to batch.